Tadano AC 3.060-2 Introduces New 60 Tonne All Terrain Crane
30-Second Takeaway
Tadano has introduced the Tadano AC 3.060-2, a 60 tonne, three axle All Terrain crane with a 50 metre main boom. Orders are open in the Americas and Australia, with first deliveries expected later in 2026 and European deliveries scheduled for 2027. The crane combines flexible road transport configurations with variable outrigger positioning and IC-1 Plus controls. Optional camera systems and compatibility with Tadano’s e-Pack extend its operating options for confined sites and applications requiring electric crane operation.
Tadano AC 3.060-2
The Tadano AC 3.060-2 expands the manufacturer’s compact All Terrain offering with a three axle crane designed for taxi crane operations. Tadano announced the introduction on 29 September 2026, confirming availability to order in the Americas and Australia.
Initial deliveries to those markets are expected before the end of 2026, with European deliveries planned for 2027. Production in Japan forms part of Tadano’s expansion of manufacturing capacity for smaller All Terrain cranes.
Equipment Specifications
The AC 3.060-2 has a maximum rated capacity of 60 tonnes and a six section, 50 metre telescopic main boom. An 8.5 to 16 metre bi-fold swingaway extension increases the maximum tip height to approximately 69 metres. With the main boom fully extended and the full 13 tonnes of counterweight installed, Tadano specifies a lifting capacity of 5.8 tonnes at an 18 metre radius. The manufacturer also reports a capacity of 2.3 tonnes at a 28 metre radius with the 16 metre extension offset at 20 degrees.
Maximum single line pull is 6.7 tonnes. With three-part reeving on the single-sheave hook block, the crane can handle loads of up to 20 tonnes within the applicable load chart.
Road Transport and Taxi Crane Configuration
The six wheel drive, all wheel steer crane can travel within 12 tonne axle loads carrying 4.2 tonnes of counterweight, the single-sheave hook block and a 300kg payload. This configuration supports jobs that can be completed using equipment carried on the crane itself.
Tadano positions the model for taxi crane duties involving travel between sites and rapid preparation for individual lifts. Its launch announcement identifies unloading, concrete work, industrial building construction and prefabricated house assembly among the intended applications.
Variable Outriggers and Crane Controls
The AC 3.060-2 incorporates Tadano’s Flex Base system, allowing the outriggers to be extended independently to accommodate obstacles and available space. IC-1 Plus crane controls, including capacity radar, calculate available lifting capacity for the configured outrigger positions.
The crane measures 2.55 metres wide and 3.71 metres high, with a carrier length of 9.49 metres. These dimensions are relevant to positioning the machine on confined construction sites and inside industrial buildings.
Optional Cameras and Electric Operation
Tadano’s optional Surround View system uses four cameras to assist crane positioning. Load and winch cameras are also available as options. With the appropriate preparation, the AC 3.060-2 can operate with Tadano’s e-Pack, enabling crane operation without local exhaust emissions. The model also shares accessories, including the runner and boom extension, with other Tadano cranes through the manufacturer’s component-sharing strategy.
Development Focus
Tadano’s development team identified compact dimensions and a broad operating range as priorities for the new crane. Performance at steep boom angles was another focus, particularly for lifting loads over obstacles.
Masafumi Nakamura of Tadano Japan’s Product Development Division said:
“This strong performance with a steep boom angle proves particularly advantageous when lifting heavy loads over obstacles.”
About Tadano
Tadano is a global manufacturer of lifting equipment, with a product portfolio covering All Terrain, rough terrain, truck and crawler cranes, alongside pick & carry cranes, loader cranes and aerial work platforms. Its equipment supports lifting and material handling across construction, infrastructure and industrial applications.
The group serves customers through regional businesses and a worldwide sales and support network. Its services include parts supply, technical support and training, while its crane technology offering includes control systems, telematics and electric operating options.
Official website: www.tadano.com
Frequently Asked Questions
What is the Tadano AC 3.060-2?
The Tadano AC 3.060-2 is a 60 tonne, three axle All Terrain crane designed for applications including taxi crane operations.
What boom and extension does it offer?
The crane has a 50 metre main boom and an 8.5 to 16 metre bi-fold swingaway extension, providing a maximum tip height of approximately 69 metres.
When will deliveries begin?
Tadano expects first deliveries in the Americas and Australia later in 2026. European deliveries are planned for 2027.
What can the crane carry within 12 tonne axle loads?
Tadano specifies a configuration carrying 4.2 tonnes of counterweight, a single-sheave hook block and a 300kg payload within 12 tonne axle loads.
Can the AC 3.060-2 operate electrically?
Yes. With the appropriate preparation, it is compatible with Tadano’s e-Pack for electric crane operation.
